Hamid SadAbadi

 

 

Personal Information

·        Full name: Hamid SadAbadi

·        Date of birth: April 18, 1983

·        Place of birth / Citizenship: Ferdows / Iranian

·        Gender: Male

·        Marital status: Single.

·        Permanent address: 1st floor, No. 5, Valley 42, 17Shahrivar St., Neyshabur, Iran, P.O. Box: 39418, Tel: +98 (551) 333-1597

·        E-mail address: hamidsadabadi@sina.kntu.ac.ir, hamidsadabadi@yahoo.com

 

Education

M.S. Degree in Mechanical Engineering (Applied Design; Dynamics & Control)

2005-2007, K. N. Toosi University of Technology, Tehran, Iran

Status: Enrolled

 

B.S. Degree in Mechanical Engineering (Solid Mechanics)

2001-2005, Ferdowsi University,Mashhad, Iran

Status: Graduated

 

Modern Management

Fall 2006, Iran Management Association (IMA), Tehran, Iran

 

Some Accomplished Projects

·        Food sterilizer; design of suitable control systems in the presence of noise and in the state of non-deterministic system parameters, Supervisor: Prof.  A. Ghaffari, summer 2005.

·        Adaptive control of a power station system, Supervisor: Prof.  A. Ghaffari, summer 2006.

·        Sliding mode control of power station system, Supervisor: Prof.  A. Ghaffari, summer 2006

·        Image processing for motion estimation by using artificial neural networks, Supervisor: Dr. Sadati, fall 2006.

 

Publications

 

Journal papers

·        M. Ghasemi, H. SadAbadi, H. Golbayani, A. Ghaffari, “ECG Characteristic Points Detection Using Wavelet Techniques and Neural Network Classifier”, Journal of Electro cardiology, Elsevier, Apr., 2007 (submitted).

·        A. Ghaffari, H. SadAbadi, M. Ghasemi, “A Mathematical Algorithm Using Windowed Analysis Approach for ECG Signal Denoising”, Biomed Pap Med Fac Univ Palacký Olomouc Czech Repub., Oct. 2006 (Accepted).

·        M. Ghasemi, H. SadAbadi, H. Golbayani, A. Ghaffari, “QT Interval Measurement; a Novel Approach Based on Wavelet Techniques and Energy Analysis”, Journal of ElectroCardiology, Elsevier, Apr., 2007 (submitted).

·        H. SadAbadi, M. Ghasemi, “Effects of Some Injection Molding Process Parameter on Fiber Orientation Tensor of Short Glass Fiber Polystyrene Composites (SGF/PS)”, Journal of Reinforced Plastics and Composites, SAGE pub, 2007 (accepted)

·        H. SadAbadi, M. Ghasemi, “Study on Fiber Weight Fraction Effect on Tensile Modulus of Polystyrene (PS) Composites reinforced With Short Glass Fiber (SGF) Based on Their Fiber Orientation”, J. of Polymer-Plastics Technology & Engineering, Taylor and Francis, 2007 (submitted)

 

Conference proceeding papers

·        M. Ghasemi, H. SadAbadi, A. Ghaffari, “A Semi-Automated QT Interval Measurement”, 33th conference of computer in cardiology, physionet/challenge2006, Valencia – Spain, 2006

·        A. Ghaffari, M. Ghasemi, H. SadAbadi, “A Semi-Automated QT Interval Measurement; A Novel Approach Based on Energy Analysis”. Intr. Conf. of Biomedical Engineering (ICBME2007), Tehran, Iran, Feb. 2007.

·        A. Ghaffari, M. Atarod, A. Rezaian, H. SadAbadi, Investigations of Some Condition on Cardiovascular Behavior Using Equivalent Electronic Circuit: Effects of Heart Rate, Heart Failure and Exercise, (Article in Persian), international Conference of BioMedical Engineering (ICBME2007), Tehran, Iran, Feb. 2007.

·        H. SadAbadi, M. Tatari, Influence of Injection Molding Parameters on Fiber Orientation Pattern of a Standard Part Injected with Short Glass Fiber PS Composites, Intr. Conf. of Mechanical Engineering (ISME2007), Tehran, Iran.

·        H. SadAbadi, S. H. Sadati, Image Interpolation for Motion Estimation using Feed forward MLP Neural Network, Intr. Conf. of Electrical Engineering (ICEE 2007), Tehran, Iran Tehran

·        S.H. Sadati, H. SadAbadi, An Intelligent Method For Linear Image interpolation; An Approach To Motion Estimation, Intr. Conf. of IASED – Germany (submitted)

 

Awards and Honors

·        Ranked 1118th in Iranian Universities Entrance Exam or Conquer with about 1’350’000 participants

·        Ranked 193th in MS program Entrance Exam for Master of Science in Mechanical Engineering with about 13,000 participants

 

Fields of Interest

·        Nonlinear Control, Stability Analysis.

·        Stochastic Control.

·        Biomedical signal processing.

·        Intelligent method in Engineering.

·        Design and Manufacturing

 

Language Proficiency

·        Native language: Persian

·        TOEFL (iBT): Attended on Nov. 10, 2007

·        GRE (PBT): Attended on Oct. 14, 2007

 

Job Experiences & Workshops

·        Summer 2003, PART-SAZAN Company, Iran-Khodro Co., Engineering Unit

·        June 2003 – Feb. 2004, Dynamic modeling of front suspension system for Iran-Khodro Co. (Internship project)

 

Seminar and Talks

1-     Injection molding technique and simulation in manufacturing engineering, PART-LASTIC Company, Mashhad, Aug. 2005

2-     TA for Mechanical Engineering Vibration and application undergraduate course, fall 2006 and spring 2007, Department of Mechanical Engineering.

Skills

·        Proficiency in MATLAB programming

·        Proficiency in modeling packages like Catia and SolidWorks

·        Proficiency in analytical and simulation packages like Adams, VisualNastran, MATLAB, and Maple

·        Competent to use Windows, Word, Excel, PowerPoint

 

References

·        Professor Ali Ghaffari, Department  of Mechanical Engineering, K. N. Toosi University of Technology, ghaffari@kntu.ac.ir

·        http://www.iranmanagement.com

·        Mechanical Engineering Department, K. N. Toosi University of Technology,

Tel: +98(21)8882991-3, +98(21)8881003

Fax: +98(21)8882997

P.O. Box: 15875-4416